WaveSplitter | Lighting the Internet on Fiber
             

10G Transceiver XFP OC192 IR2 & ER/EW

157 views
0 Likes
0 0
10GBase ER/EW XFP Optical Transceivers

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

7. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 7 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Recommended Interface Circuit Typical Application Circuit For Power Supply XFP Connector

3. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 3 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Note2. Measured at 10.3125Gbps,Non-framed PRBS2 ^31 -1,NRZ. Note3. Receiver sensitivity is informative. Stressed receiver sensiti vity shall be measured with conformance test signal for BER =1x 10 -12 . Note4. Vertical eye closure penalty and stressed eye jitter are t he test conditions for measuring stressed receiver sensitiv ity. They are not the required characteristic of the receiver . Digital Diagnostic Memory Map EEPROM Serial ID Memory Contents Accessing Serial ID Memory uses the 2 wire address 1010000X (A0H). Memory Contents of Serial ID are shown in Tabl e 2.

9. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 9 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Modification History Revision Date Description Originator Review Approved V1 29-Apr-2010 New Issue Tina Tang Wayne Liao Wayne Liao America Headquarters 46824 Lakeview Blvd. Fremont, CA 94538 USA Tel: 510-651-7800 Fax: 510-651-7822 Taipei Branch 5F, No 3-2 (Building H), Yuan-Qu Street Nan-kang, Taipei 115, Taiwan Tel: +886-2-2782-5780 Fax: +886-2-2782-5782 ShenZhen Branch 5F, 7th Building, Tian'an Industrial Zone, NanShan Area, ShenZhen,China Tel: +86-755-86265980 ; Fax: +86-755-26642741 All specification data are accurate on the date of publication for product comparisons and ordering in formation. Wavesplitter Technologies, Inc. reserves the right to change specifications without notice.

5. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 5 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Pin Description Module Electrical Pin Definition Pin Logic Symbol Name/Description Note 1 GND Module Ground 1 2 VEE5 Optional -5.2V Power Supply ( Not Required ) 3 LVTTL-I Mod_DeSel Module De-select; When held low allows module to respond to 2-wire serial interface 4 LVTTL-O Interrupt — — — — — — Interrupt — — — — — — ; Indicates presence of an important condition which can be read over the 2-wire serial interface 2 5 LVTTL-I TX_DIS Transmitter Disable; Turns off trans mitter laser output 6 VCC5 +5V Power Supply 7 GND Module Ground 1 8 VCC3 +3.3V Power Supply 9 VCC3 +3.3V Power Supply 10 LVTTL-I/O SCL 2-Wire Serial Interface Clock 2 11 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2 12 LVTTL-O Mod_Abs Indicates Module is not present. Grounded in th e Module 2

8. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 8 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Multi-Sourcing Agreement (MSA) Regulatory Compliance Feature Test Method Performance Laser Eye Safety FDA 21 CFR 1040.10 and 1040.11 IEC 60825-1: 1994+ A11: 1996+ A2: 2001 IEC 60825-2: 2004 + A1: 2006 EN 60825-1:1994+A1:2002+A2:2001 EN 60825-2: 2004 Compliant with Class 1 laser product Electrostatic Discharge (ESD) to the Electrical Pins MIL-STD-883E Method 3015.7 Human Body Model Class 1 (>1.5kV) Electrostatic Discharge (ESD) Immunity IEC 61000-4-2: 2001 Class 2 (>4.0kV) Electromagnetic Interference (EMI) FCC Part 15 Subpart J Class B CISPR22:1997+A1:2000+A2:2002, Class B EN55022:1998+A1:2000+A2:2003, Class B Compliant with standards Ordering Information Specification Part No Package Data rate Laser Optical Power Detector Sensitivity Temp. Reach Other Application code WST-XFP-IR2-C XFP 9.95Gbps ~10.7Gbps 1550nm EML -1~ 2dBm PIN -14dBm 0~70 o C 40km DDM RoHS OC-192(IR-2)/ SDH(STM S-64.2b) 10GBASE-ER/EW 10G Fibre Channel

4. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 4 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Serial ID Memory Contents Data Address Size (Bytes) Name of Field Contents(Hex) Description BASE ID FIELDS 128 1 Identifier 06 XFP 129 1 Ext. Identifier 90 Max :3.5W, CDR 130 1 Connector 07 LC Connector 131-138 8 Transceiver 22 00 00 00 00 20 00 00 10GBASE-ER/EW, STM S-64.2b 139 1 Encoding 30 SONET Scrambled, NRZ 140 1 BR-Min 63 9.95Gbps 141 1 BR-Max 6B 10.70Gbps 142 1 Length (SMF)-km 28 40km 143 1 Length (E-50um) 00 144 1 Length(50um) 00 145 1 Length(62.5um) 00 146 1 Length (Copper) 00 147 1 Device Tech 74 1550nm EML, PIN Detector 148-163 16 Vendor name 57 41 56 45 53 50 4C 49 54 54 45 52 20 20 20 20 WAVESPLITTER 164 1 CDR Support F0 CDR supports 9.953Gbps~10.75Gbps 165-167 3 Vendor OUI 00 00 00 168-183 16 Vendor PN 57 53 54 2D 58 46 50 2D 49 52 02 2D 43 20 20 20 WST-XFP-IR2-C 184-185 2 Vendor rev xx xx 186-187 2 Wavelength 79 18 1550nm 188-189 2 Wavelength Tolerance 0F A0 +/- 20nm 190 1 Max Case Temp 46 70degC 191 1 CC_BASE Check sum of bytes 128 – 190 192-195 4 Power Supply AF FF 68 00 3.5W(max), 500mA/800mA +5.0V/+3.3V 196-211 16 Vendor SN xxxxxxxxxxxxxxxx 212-219 8 Data code xxxxxxxxxxxxxxxx Yesr(2bytes),Month(2byes),Day(2 bytes) 220 1 Diagnostic Monitoring Type 08 No BER Support,Average Power 221 1 Enhanced Options 60 Optional Soft Tx_Disable and P_Down 222 1 Aux Monitoring 77 +3.3V Supply Voltage 223 1 CC_EXT xx Check sum of bytes 192 – 222 224-255 32 Vendor Specific Vendor Specific EEPROM

6. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 6 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C 13 LVTTL-O Mod_NR Module Not Ready; Indicating Module Operation al Fault 2 14 LVTTL-O RX_LOS Receiver Loss Of Signal Indicator 2 15 GND Module Ground 1 16 GND Module Ground 1 17 CML-O RD- Receiver Inverted Data Output 18 CML-O RD+ Receiver Non-Inverted Data Output 19 GND Module Ground 1 20 VCC2 +1.8V Power Supply ( Not Required ) 21 LVTTL-I P_Down/RST Power down; When high, requires the module to limit power consumption to 1.5W or below. 2-Wire serial interface must be function al in the low power mode. Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle . 22 VCC2 +1.8V Power Supply ( Not Required ) 23 GND Module Ground 1 24 PECL-I RefCLK+ Reference Clock Non-Inverted Input, AC co upled on the host board ( Not Required ) 25 PECL-I RefCLK- Reference Clock Inverted Input, AC couple d on the host board ( Not Required ) 26 GND Module Ground 1 27 GND Module Ground 1 28 CML-I TD- Transmitter Inverted Data Input 29 CML-I TD+ Transmitter Non-Inverted Data Input 30 GND Module Ground 1 Note1: Module ground pins GND are isolated from the module case and chassis ground within the module. Note2: Shall be pulled up with 4.7K-10Kohms to a voltage b etween 3.15V and 3.45V on the host board. Block Diagram

1. DataSheet All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 1 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Absolute Maximum Ratings Parameter Symbol Unit Min Max Storage Temperature Range T s o C -40 +85 Power Supply Voltage V cc V -0.5 +3.6 Operating Case Temperature T c o C 0 +70 Recommended Operating Conditions Parameter Symbol Unit Min Typ Max Note Case Operating Temperature Range T c o C 0 +70 Power Supply Voltage V cc3 V 3.135 3.3 3.465 Power Supply Current I cc3 mA 750 Power Supply Voltage V cc5 V 4.75 5.25 Power Supply Current Icc 5 mA 300 Data rate Gbps 9.95 10.70 1 Features:  Compliant with XFP MSA  Support 10GE application at the data-rate of 10.3125Gbps and 9.953Gbps  1550nm cooled EML and PIN receiver  XFI electrical interface  2-wire interface for integrated Digital Diagnostic monitoring  XFP MSA package with duplex LC connector  Very low EMI and excellent ESD protection  Hot Pluggable  +3.3V & +5V power supply  Power consumption less than 3.5 W  Operating case temperature range: 0°C~70°C Applications:  SONET(OC-192 IR-2)/SDH(STM S-64.2b)  10GBASE-ER/EW 10Gigabit Ethernet  10GE Storage  10GE Ethernet switches and routers

2. All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 2 of 9 10GBase ER/EW XFP Optical Transceivers WST-XFP-IR2-C Specifications (tested under recommended operating conditions, unless ot herwise noted) Parameter Symbol Unit Min. Typ. Max. Notes Electrical Characteristics Supply Current Icc mA 1000 Transmitter Differential Input Voltage V IN mV pp 120 820 Receiver Differential Output Voltage V O mV pp 340 650 850 V OH Vcc-0.5 Vcc Loss of Signal (LOS) V OL V Gnd Gnd+0.5 V IH 2.0 Vcc Transmitter Disable (TX-Disable) V IL V Gnd Gnd+0.8 Optical transmitter Characteristics Average Launch Power Po dBm -1 2 2 Center wavelength λ c nm 1530 1565 Side Mode Suppression Ratio SMSR nm 30 Extinction ratio  E R dB 8.2 2 Transmitter and dispersion penalty(max)  TDP dB 3 Optical power OMA P OMA dBm -1.7 OMA-TDP P OMA-TDP dBm -2.1 Average launch power of OFF transmitted P off dBm -30 RIN 12 OMA RIN dB/Hz -128 Generation Jitter 1 (20kHz - 80MHz) UI p-p 0.15 Generation Jitter 2 (4MHz - 80MHz) UI p-p 0.1 Optical Return Loss Tolerance dB 21 Output eye Compliant with IEEE802.3ae eye mask & GR-253-CORE/ITU-T G.691 Optical receiver Characteristics Center wavelength λ c nm 1260 1600 Average receiver power(max) P max dBm -1 Average receiver power(min) P min dBm -15.8 Receiver Reflectance R rx dB -26 Receiver Sensitivity in OMA dBm -14 Stressed Sensitivity in OMA dBm -11.3 3 Vertical eye closure penalty dB 2.7 4 Stressed eye jitter UIp-p 0.3 3 Assert LOS A dBm -30 LOS Deassert LOS D dBm -14 LOS Hysteresis LOS H dB 0.5 Note1. Data rate tolerance: IR-2/S-64.2b, 10GBASE-EW:typ.+/- 20ppm, 10GBASE-ER: typ.+/-100ppm

Views

  • 157 Total Views
  • 85 Website Views
  • 72 Embedded Views

Actions

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 2

  • 8 www.wavesplitter.com
  • 3 18.220.135.215