WaveSplitter | Lighting the Internet on Fiber
             

1000Base T SFP (non-DDM)

827 views
0 Likes
0 0
1000Base-T SFP Transceiver Modules (non DDM version)

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

6. All contents are Copyright © 1996 - 2010 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 6 of 8 Document Number: 95-0026-V1 1000Base-T SFP Transceiver Modules (non DDM version) WST-SEAxxV-x6 Typical Application Circuit Required Host Board Components

5. All contents are Copyright © 1996 - 2010 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 5 of 8 Document Number: 95-0026-V1 1000Base-T SFP Transceiver Modules (non DDM version) WST-SEAxxV-x6 15 VCCR Receiver Power Supply 2 16 VCCT Transmitter Power Supply 2 17 VEET Transmitter Ground 1 1 18 TD+ Transmitter Non-Inverted DATA in. 3 19 TD- Transmitter Inverted DATA in. 3 20 VEET Transmitter Ground 1 1 Note1: TX Fault is not used and tied to ground via a 100ohm resistor. Note2: TX Disable as described in the MSA is not appli cable to the 1000BASE-T module, but is used for conveni ence as an input to reset the internal PHY Low (0 – 0.4V): Transceiver on Between (0.4V and 2.0 V): Undefined High (2.0 – 3.465 V): Transceiver in reset state Open: Transceiver in reset state Note3: MOD-DEF 0,1,2 are the module definition pins . They should be pulled up with a 4.7k~10kohm resistor on the host board. The pull-up voltage shall be VccT or VccR. MOD-DEF 0 is tied to ground within the module. MOD-DEF 1 is the clock line of two wire serial i nterface for serial ID MOD-DEF 2 is the data line of two wire serial i nterface for serial ID Note4: LOS is not used and is always tied to ground via a 100ohm resistor Note5: These are the differential receiver output. The y are internally AC-coupled 100 Ω differential lines which should be terminated with 100 Ω (differential) at the user side. Note6: These are the differential transmitter inputs . They are AC-coupled, differential lines with 100 Ω differential termination inside the module.

2. All contents are Copyright © 1996 - 2010 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 2 of 8 Document Number: 95-0026-V1 1000Base-T SFP Transceiver Modules (non DDM version) WST-SEAxxV-x6 Parameter Symbol Unit Min Typ Max Notes Electrical characteristics Data Input Swing Differential V INP-P mV 500 2400 1 Data Output Swing Differential V OUTP-P mV 350 1200 1400 2 Module Reset Swing Differential s 10 3 Data Rate Mbps 10 1000 4 Bit Error Rate BER 10^-10 5 Output Data Rise/Fall Time psec 180 6 Serial ID Clock Rate KHz 100 Note1. Internally ac coupled and terminated (100 Ohm differential). Note2. Internally ac coupled with an external 100 ohm differential load termination. Note3. Time from rising edge of Tx Disable until l ink comes down. Note4. 10/100/1000 BASE-T operation requires the h ost system to have an SGMII interface with no clocks, and the module will operate as 1000BASE-T only when the hos t system use SERDES interface. Note5. Measure over 100m Cat-5 UTP cable. Note6. 20%-80% rise and fall times measured from t he module’s internally generated Gigabit Ethernet id le pattern at 1.25 Gbps Memory Map

4. All contents are Copyright © 1996 - 2010 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 4 of 8 Document Number: 95-0026-V1 1000Base-T SFP Transceiver Modules (non DDM version) WST-SEAxxV-x6 92-94 3 Reserved 00 00 00 95 1 CC EXT xx 96-255 160 Vendor specific Pin Descript i on Pin Name Function/Description Engagement order Note s 1 VEET Transmitter Ground 1 1 2 TX Fault Transmitter Fault Indication 3 2 3 TX Disable Transmitter Disable-Module disables on hig h 3 3 4 MOD_DEF2 Module Definition 2-Two wire serial ID 3 5 MOD_DEF1 Module Definition 1-Two wire serial ID 3 6 MOD_DEF0 Module Definition 0-Two wire serial ID 3 2 7 Rate Select Not connected 3 8 LOS Loss of Signal indication. Logic 0 indicates 3 2 9 VEER Receiver Ground 1 10 VEER Receiver Ground 1 1 11 VEER Receiver Ground 1 1 12 RD- Receiver Inverted DATA out. 3 13 RD+ Receiver Non-inverted DATA out. 3 14 VEER Receiver Ground 1 1

7. All contents are Copyright © 1996 - 2010 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 7 of 8 Document Number: 95-0026-V1 1000Base-T SFP Transceiver Modules (non DDM version) WST-SEAxxV-x6 Package Outline Unit is millimeter. All dimensions are ±0.1mm unles s otherwise specified. RO TA TE 90 TO EJE CT FR OM CA GE 2.5 67.35 63.75 13.7 14 13.4 45 8.5 + - 0.1 + - 0.1 + - 0.1 Regulatory Compliance Feature Test Method Performance RoHS6 BS EN 1122: 2001 US EPA METHOD 3050B US EPA METHOD 3052 US EPA METHOD 3060A Pb <1000ppm Cr6+ <1000ppm Hg <1000ppm PBB <1000ppm PBDE <1000ppm Cd <100ppm

8. All contents are Copyright © 1996 - 2010 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 8 of 8 Document Number: 95-0026-V1 1000Base-T SFP Transceiver Modules (non DDM version) WST-SEAxxV-x6 Ordering Information Specification Part No. Package Interface Media Data Rate Temp Reach Note RoHS WST-SEAMCV -D6 SFP Electric, SGMII Copper (Cat5 UTP Cable) 10/100/1000 Base 0~70 °C 100m Auto-Negotiation enable, support Rx_LOS RoHS6 WST-SEACCV -D6 SFP Electric, SERDES Copper (Cat5 UTP Cable) 1000Base 0~70 °C 100m Auto-Negotiation enable, support Rx_LOS RoHS6 WST-SEACCV -A6 SFP Electric, SERDES Copper (Cat5 UTP Cable) 1000Base 0~70 °C 100m Auto-Negotiation enable RoHS6 WST-SEACCV -R6 SFP Electric, SERDES Copper (Cat5 UTP Cable) 1000Base 0~70 °C 100m Auto-Negotiation disable, support Rx_LOS RoHS6 WST-SEAMIV- D6 SFP Electric, SGMII Copper (Cat5 UTP Cable) 10/100/1000 Base -40~85 °C 100m Auto-Negotiation enable, support Rx_LOS RoHS6 WST-SEACIV- D6 SFP Electric, SERDES Copper (Cat5 UTP Cable) 1000Base -40~85 °C 100m Auto-Negotiation enable, support Rx_LOS RoHS6 Modification History Revision Date Description Originator Review Approve d V1 14-May-2010 New Issue Tina Tang Wayne Liao Wayne Liao America Headquarters 46824 Lakeview Blvd. Fremont, CA 94538 USA Tel: 510-651-7800 Fax: 510-651-7822 Taipei Branch 5F, No 3-2 (Building H), Yuan-Qu Street Nan-kang, Taipei 115, Taiwan R.O.C. Tel: +886-2-2782-5780 Fax: +886-2-2782-5782 ShenZhen Branch 5F, 7th Building, Tian'an Industrial Zone, Dengliang Road, NanShan Area, ShenZhen China Tel: +86-755-86265980 ; Fax: +86-755-26642741 All specification data are accurate on the date of publication for product comparisons and ordering in formation. Wavesplitter Technologies, Inc. reserves the right to change specifications without notice.

3. All contents are Copyright © 1996 - 2010 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 3 of 8 Document Number: 95-0026-V1 1000Base-T SFP Transceiver Modules (non DDM version) WST-SEAxxV-x6 EEPROM Serial ID Memory Contents Accessing Serial I D Memory uses the 2 wire add ress 1010 000X (A0h). Mem ory Contents of Serial ID are shown in Table 2. Data Address Size (Bytes) Name of Field Contents(Hex) Description BASE ID FIELDS 0 1 Identifier 03 SFP 1 1 Ext. Identifier 04 GBIC/SFP function is defined b y two Wire interface ID only 2 1 Connector 00 3-10 8 Transceiver 00 00 00 08 00 00 00 00 1000BASE-T 11 1 Encoding 01 8B/10B 12 1 BR-Normal 0D 1.25Gbps 13 1 Rate Identifer 00 unspecified 14 1 Length (9um)-km 00 15 1 Length (9um) 00 16 1 Length(50um) 00 17 1 Length(62.5um) 00 18 1 Length (Copper) 64 100m 19 1 Length(OM3) 00 20-35 16 Vendor name 57 41 56 45 53 50 4C 49 54 54 45 52 20 20 20 20 “WAVESPLITTER”(ASCII) 36 1 Channel Spacing 00 37-39 3 Vendor OUI 00 00 00 40-55 16 Vendor PN 57 53 54 2D 53 45 41 xx xx 56 2D xx 36 20 20 20 Transceiver part number “WST-SEAxxV-x6” 56-59 4 Vendor rev xx xx xx xx 60-61 2 Wavelength 00 00 62 1 Reserved 00 63 1 CC Base xx 64-65 2 Options 00 00 66 1 BR,max 00 67 1 BR,min 00 68-83 16 Verdor SN xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx 84-91 8 Data code xx xx xx xx xx xx xx xx T able 2 S e ri a l I D M e m o r y C o n tents

1. DataSheet All contents are Copyright © 1996 - 2009 W avesplitt er Technologies, Inc. All rights reserved. Prelimin ary and Proprietary www.wavesplitter.com Page 1 of 8 1000Base - T SF P Transceiver Module s (non DDM version) WST-SEAxxV-x6 Absolute Maximum Ratings Parameter Symbol Unit Min Max Storage Temperature Range Ts °C -40 +85 Power Supply Voltage V cc V -0.5 +3.6 Recommended Operating Conditions Parameter Symbol Unit Min Typ Max Case Operating Temperature -CT T C-CT °C 0 70 Case Operating Temperature - IT T C-IT °C -40 85 Power Supply Voltage Vcc V 3.135 3.3 3.465 Power Supply Current Icc mA 390 Specifications (t est ed under r ecomm ended operating conditions, unl ess other wise not ed) Features:  Up to 1.25Gbps bi-directional data links  SFP form with compact RJ-45 connector  Single +3.3V power supply, low Power dissipation  1000 BASE-T operation in host systems with SERDES interface or 10/100/1000 BASE-T operation in host systems with SGMII interface  Intelligent Auto-Negotiation support for automatic duplex, speed, and flow control resolution  Link lengths at 1.25 Gbps: up to 100 meter reach over unshielded twisted-pair category-5 cable.  Detailed product information in EEPROM  Physical layer IC can be accessed via 2-wire serial bus  Operating temperature range: Commercial Temperature: 0 o C ~ +70 o C Industrial Temperature: -40 o C ~ +85 o C Applications:  LAN 1000Base-T  Switch to Switch Interface  Router/Server interface  Switched backplane applications Standards:  Compatible with SFP MSA  Compatible with IEEE Std 802.3TM-2002

Views

  • 827 Total Views
  • 88 Website Views
  • 739 Embedded Views

Actions

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 2

  • 7 www.wavesplitter.com
  • 1 18.220.135.215